USER MANUAL

Skullcandy Sesh Evo / XT Evo

Auto Pair Mode

Auto Power On

Auto Power off

Charge Earbuds

Charge Case

Pairing Mode

Off Mode

Pairing New Device

“Sesh Evo”

Power on

Left side and right side

Power off

Left side and right side

Play / Pause

Left Side or Right Side

Tracked Forward

Right Side

Tracked Back

left Side

Volume UP

Right Side

Volume down

left Side

Answer / End

Left Side or Right Side

Active Voice Assistant

Left Side or Right Side

Clear Paired Device

Left Side or Right Side

Off Mode

Tile Enabled:

Download the App

Pair Tile

3 EQ Modes

Left Side or Right Side

Music, Movie and Podcast

Change Aqualizer Mode

Questions visit: Skullcandy.com

Speaker Driver: 6mm, Impedance: 32 Ohms, THD <3%@1KHz, Voltage Regulation: 5V, 500mA, Bluetooth® 5.0, Frequency Band: 2402MHz – 2480MHz, Maximum Power: 10mw, Weight: 63,5g
Skullcandy, and other marks are registered trademarks of Skullcandy, Inc. All rights reserved,
Maximum operating temperature 45°C.

TROUBLESHOOTING

PAIRING ISSUES?

ISSUE: The biggest challenge with true wireless earbuds is ensuring your buds are properly connected to each other and your device. There are times when users will unintentionally disconnect the buds and change their paired state, this can create pairing challenges and impact your ability to use either bud solo (Master Role Switching). Do not worry, as this is an easy fix!

SOLUTION:

To ensure ease of re-pairing, please unpair or forget your SESH® EVO in your paired Bluetooth device list.
Remove the SESH® EVO from the charging case and Manually Power OFF:
1. Touch and hold BOTH buds for 6 seconds
Once both buds have been powered OFF:
1. Touch and hold each bud for 10 seconds to completely reset them (this will power cycle them on and off again).
Once both buds have gone through the power cycle:
1. Place the buds back in the case until both LED’s show red, and then pull them back out.
2. Both buds will automatically power ON and the LED’s will simultaneously flash BLUE while they sync to each other.
Once the buds have synced together:
1. You will hear a tone to indicate the sync was successful and ONLY the LEFT bud will begin to flash RED/BLUE.
At this time, turn on your device’s Bluetooth and look for SESH® EVO in your list of Available Bluetooth devices . Please make sure it only appears once, and select it.
1. IMPORTANT – Select all “Pair” and “Ok” prompts that will pop up on your screen.
2. Once successfully paired, a voice prompt will notify you are now “Connected”

*** WHEN PAIRING TO YOUR SESH®️ EVO, BE SURE TO ONLY SELECT THE PRODUCT NAME FROM THE AVAILABLE DEVICE PAIRING LIST (IT WILL APPEAR EXACTLY AS “SESH EVO”). ***

Since your Tile® enabled product gives off different Bluetooth connection points, you will also see your product name followed by –LE, such as “Sesh Evo-LE”. You don’t want to select this when it appears in your available devices list. This is the Low-Energy Bluetooth connection that the Tile® App uses for their bud tracking functionality.

USE EITHER BUD SOLO

ISSUE: If you would like to use the SESH® EVO with only one earbud (audio will switch from Stereo Mode to Mono Mode), you’re in luck! The updated technology in SESH® EVO allows you to use either the left OR the right bud alone. Once paired correctly, you will be able to switch between buds at your discretion. Although, if you’re having any challenges switching between buds, you may follow these simple steps to ensure ease of use when pairing and switching between Mono and Stereo Modes.

SOLUTION:

PLEASE NOTE – BOTH THE LEFT AND RIGHT BUD FOR SESH® EVO CAN BE USED IN MONO MODE, THIS IS BECAUSE THE NEW TECH ALLOWS MASTER ROLE SWITCHING CAPABILITIES.
For the optimal Mono Mode functionality, first Power On and pair your buds to your device normally or as described in our troubleshooting section. This will ensure the seamless transition between Stereo and Mono modes.
Once both SESH® EVO buds are paired together, simply place the RIGHT or LEFT bud back into the case; whichever you prefer! The remaining bud will stay paired and function with both phone calls and music.
You will maintain bud functionality, but remember you will lose some of the media control functionality such as “Volume +/-“, and “Track <</>>”, depending on which bud you are using in Mono Mode. The RIGHT bud will always control Volume Up and Track forward, and the LEFT bud will always control Track Back.
If you would like to change back to Stereo Mode from Mono Mode, simply pull the other bud from the case at any time and you will hear a tone, or the music will seamlessly begin to stream to indicate that you have automatically entered back into Stereo Mode.
PLEASE NOTE – If you’re having any trouble switching between the LEFT and RIGHT buds in Mono Mode, you will need to follow the reset instructions explained above and clear BOTH earbuds and re-pair them to enter back into the correct paired state to allow you to use them together or solo.

BUDS NOT CHARGING IN CASE/CASE LID NOT CLOSING PROPERLY?

ISSUE: Not seeing the RED LED indicator on the bud when you’ve placed your SESH® EVO back in the case?

SOLUTION:

Wait momentarily as the buds connect, occasionally it takes a few seconds to begin charging
Check to see if any debris is blocking the charging pins in the case, or on the bud
Check to see if the removable in-ear gels are placed correctly on the acoustic port, this could be keeping the buds from sitting correctly in the case
This same issue could also be interfering with your case lid when closing, if you’re having a hard time closing the lid correctly, this is an indicator that buds are not set correctly or the gels are interfering.
When charging the device, we recommend using a cable, charger, or outlet with a power output that does not exceed 18-Watt (5 Volts/3.6amps).

If you’ve checked everything above and are still experiencing issues and/or if the indicator light remains dark and does not come on at all, please visit our warranty page where you can file a claim to receive a replacement product. All Skullcandy products have a 1-year warranty.

TILE

ACTIVATING TILE

HERE ARE MORE DETAILED ACTIVATION INSTRUCTIONS:

Download and open the Tile app on your smartphone or tablet
Tap the + on the top left corner of your screen
On the Add a Device page, choose Skullcandy and select the Tile enabled headphones
Press the button on your Tile device and listen for the tune
Hold the Tile close to your device until they connect, it should take about ten seconds
That is all! Your Skullcandy headphones are now activated with Tile!

LOCATING YOUR DEVICE WITH TILE

When searching for misplaced headphones, use the Tile app to audibly locate them. In the Tile app, tap “find” and listen for your headphones playing the Tile tune.
Detailed instructions on how to ring your headphones:
Ring your Tile from the Tile app when it is within Bluetooth range
Open up the Tile app to find your list of Tiles.
Tap the headphones you want to ring.
Tap the green “Find” button
Listen for the Tile tune!
After you’ve found your Tile, tap the blue “Done” button or press once firmly on the Tile button to make your Tile stop ringing.

FAQS

BATTERY & CHARGE

WHAT IS THE TOTAL CHARGING TIME FOR SESH® EVO?

1 hour for the earbuds to charge to 100% inside the case
2 hours for the case to charge to 100%

BATTERY LIFE AND PLAY TIME IS VERY IMPORTANT TO ME. HOW LONG DOES THE SESH® EVO LAST?

There is up to 5+ hours of play time in the earbuds, and up to 19+ hours in the case, allowing up to 24 Hours of total play time.

CAN I CHARGE SESH® EVO WITH MY SKULLCANDY POWER ACCESSORIES/PC/LAPTOP/?

Pretty much all USB-C charging cables will work to charge your SESH® EVO earbuds.

DOES SESH® EVO HAVE SOME SORT OF FAST CHARGE?

YES! – SESH® EVO has Rapid Charge technology featuring a USB-C charging port and cable.
10 Minutes of charge for the earbuds will provide 2+ hours of playtime, and 10 minutes of charge in the charging case will provide 4 hours of playtime.

NEW FEATURES

WHAT IS THE BENEFIT OF THE USE EITHER BUD SOLO FEATURE AND FUNCTIONALITY?

This feature also allows you to utilize either the LEFT or RIGHT bud in Mono/Solo Mode, rather than being limited to just one specific side.

HOW DO YOU CHANGE BETWEEN EQ SETTINGS, AND WHAT’S THE DIFFERENCE?

While paired, you simply press the LEFT or RIGHT bud 4x and you will hear a voice prompt notifying you each time it changes to a new preset EQ. You will cycle through the EQ modes each time you complete the 4x tap. The 3 modes are Music Mode, Podcast Mode, and Movie Mode.
Your default EQ setting is “Music Mode”, great for general listening.
Podcast mode removes most of the bass response and is great for podcasts or narrated books.
Movie mode is great for most media, increasing the loudness and bass just a bit to enhance your favorite action-packed shows and movies.

WHAT IS THE TILE® TRACKING FEATURE AND HOW DOES IT WORK?

The TILE® tracking feature will allow you to locate your earbuds if you’ve misplaced them or they have been taken.
You will need to download the TILE App for this feature to function with your device, and it is very easy to set up!
Simply follow the steps for TILE® to find your device, and with a single tap on each bud you will have them connected and ready to track anytime necessary.
Once your earbuds are ready to track from the TILE App, you can track them on a map, as well as sound a tone from each bud.

DOES THE SESH® EVO SOUND BETTER THAN THE PREVIOUS SESH®? (OPTIONAL ADD)

Yes, we’ve integrated a new driver and improved tuning for a more premium listening experience.

CONNECTION

DOES THE SESH® EVO PAIR WITH SKULLCANDY APP?

Sorry but the SESH® EVO will not pair with the SKULLCANDY APP.

WHAT IS THE BLUETOOTH RANGE OF THE SESH® EVO?

You will be able to listen up to 30+ feet (10+ meters) away from your paired device, though your connection experience may vary based on your environment.

CAN I CONNECT SESH® EVO TO A COMPUTER?

Yes as well as to a phone, tablet, MP3 player, laptop, or anything else with a Bluetooth connection.

CAN I USE SESH® EVO WITH A PS4/XBOX ONE/SWITCH?

Xbox One: No
Switch: Yes
PS4: No

WHICH VERSION OF BLUETOOTH DOES SESH® EVO USE?

Bluetooth® version 5.0

WHICH SIDE OF SESH® EVO IS CONSIDERED THE “MASTER” BUD?

The LEFT and RIGHT side earbud can be your master earbud, so either bud can be used in Mono Mode (one earbud listening).

WHEN ON A CALL OR LISTENING TO MY CONTENT, WILL I HEAR AUDIO IN ONE OR BOTH EARBUDS?

SESH® EVO has stereo calling and streaming so you’ll always hear the caller or your content in both ears.
Although, you do have the option to use only one earbud (left or right side) if you prefer mono mode in some situations.

GENERAL QUESTIONS

CAN I USE SIRI/GOOGLE ASSISTANT/ALEXA WITH MY SESH® EVO?

When paired to your device, you can press the LEFT or RIGHT bud 3x to activate your voice assistant feature at any time.

CAN I USE SESH® EVO FOR SPORTS OR WORKING OUT?

Yes! SESH® EVO is sweat, water, and dust resistant (IP55).

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

ISED Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference
This device must accept any interference, including interference that may cause undesired operation of the device.

ISED SAR Compliance Statement

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

Americas Skullcandy, Inc. 6301 N Landmark Dr. Park City, UT 84098 U.S.A. Skullcandy.com

Europe Skullcandy Europe BV Postbus 425 5500AK Veldhoven Nederland Skullcandy.eu

México Skullcandy Mexico S de RL de CV Aristoteles 218 Polanco IV Seccion, Miguel Hidalgo 11550, México City, México Skullcandy.mx

Canada Skullcandy Canada ULC 329 Railway St. Unit 205 Vancouver, BC. V6A 1A4 Canada Skullcandy.ca

Contains Li-ion battery. Battery must be recycled or disposed of properly.

Made in China

MODEL: S2TVW

FCC ID Y22 S2TVW

IC 10486A-S2TVW