Flash Furniture Yo-gym80015-bk-gg 28 Inch Square Gas Burning Firepit Table Instruction Manual

• Tighten all components securely before use to avoid personal
  injury.
• Do not use any sharp objects to open plastic wrapped components
  as it may cause damage.

1. Leg Assembly:

• Place the Tabletop with Burner (Part G) facedown on a clean
  smooth surface.
• Connect the Front Right Leg (Part A) and Front Left Leg (Part
  D) to the front of the Tabletop using (4) M6x10mm Bolts (Part
  AA).
• Connect the Back Right Leg (Part B) and Back Left Leg (Part C)
  using (4) M6x10mm Bolts (Part AA).
• Ensure that the Control Unit is located between Legs A and
  B.

• Connect the Side Panel with Window (Part J) to the Front Right
  Leg (Part A) and Back Right Leg (Part B) using (4) M6x10mm Bolts
  (Part AA). Make sure the Control Panel fits through the
  window.
• Connect the Side Panel (Part I) to the Front Left Leg (D) and
  Back Left Leg (C) using (4) M6x10mm Bolts (Part AA).
• Connect the remaining Side Panel to the Back Legs (Parts B and
  C) using (4) M6x10mm Bolts (Part AA).
• Secure the Control Panel to the Side Panel with Window (Part J)
  using (4) MSx10mm Bolts (Part BB) and (4) MS Nuts (Part CC).

• Connect the Gas Tank Support (Part K) to the body using (4)
  M6x10mm Bolts (Part AA).
• Tighten all bolts (AA) with a Phillips Screwdriver.

Thank you for your purchase!
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury. DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may result.
Warning:
CHOKING HAZARD – Small Parts. Adult Assembly Required. DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision. To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Customer Service Email: [email protected] | Phone: 866-552-2810
YO-GYM80015-BK-GG

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of longlasting consumer relationships. We strive toward excellence in all we do and want you to be completely satisfied with your purchase. Please contact our exceptional Customer Experience Agents at the email address or phone number shown below to assist you with any product questions or issues before requesting a return. We look forward to serving you in a friendly, efficient manner to resolve any issues you may have.
Customer Service Email: [email protected] Customer Service Phone: 866-552-2810
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product is warranted from the original purchase date and to the original purchaser for normal usage, according to the below-referenced specifications and limitations.
Non-moving metal parts are warranted for 5 years. Component parts including pneumatic cylinder, control mechanism, base and casters are warranted for 2 years. All other items are warranted for 1 year. Normal usage means use in compliance with the restrictions and weight limits specified for the product. In the absence of product-specific restrictions and weight limits, normal usage means use for no more than forty hours per week by persons weighing 250 lbs. or less. Coverage terminates if the product is sold or otherwise transferred. Repairs made by parties other than Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence, alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any other event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of leather or fabric; (3) cosmetic damage that may result from normal usage; (4) damage attributable to use by persons exceeding specified weight limits or commercial use exceeding forty hours per week; or (5) rust or other damage caused by exposure to moisture. The user assumes all risk of injury resulting from use of this product. Liability for incidental or consequential damage is excluded. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

please contact 866-552-2810 for further for further assistance.

Cover Lava Rock
Tabletop with Burner Back Left Leg

Side Panel

Back Right Leg

Front Left Leg
Door
Front Right Leg Back Right Leg Back Left Leg Front Left Leg

Gas Tank Support

Side Panel with Window Front Right Leg

Assembly

1 Leg Assembly
o Place Tabletop with Burner (Part G) facedown on a clean smooth surface. Connect Front Right Leg (Part A) & Front Left Leg (Part D) to the front of the Tabletop using (4) M6x10mm Bolts (Part AA). Connect Back Right Leg (Part B) & Back Left Leg (Part C) using (4) M6x10mm Bolts (Part AA).

Back Right Leg

Back Left Leg

Front Right Leg

Front Left Leg

NOTE: ENSURE CONTROL UNIT IS LOCATED BETWEEN LEGS A & B.

M6x10mm Bolts

DO NOT COMPLETELY TIGHTEN THE HARDWARE AT THIS TIME.

2 Side Panel Assembly

Connect Side Panel with Window (Part J) to Front Right Leg (Part A) and Back Right Leg (Part B) using (4) M6x10mm Bolts (Part AA). Ensure Control Panel fits through window.

Connect Side Panel (Part I) to Front Left Leg

(D) and Back Left Leg (C) using (4) M6 x10

Bolts (Part AA). Connect remaining Side Panel

to Back Legs (Parts B & C) using (4)

M6x10mm Bolts (Part AA).

cc
M5 Nut

BB

Back Right Leg
Side Panel with Window

Back Left Leg Side Panel
A

M6x10mm Bolt Side Panel
Front Left Leg

MS x10mm Bolt
o Secure the Control Panel to Side Panel with Window (Part J) using (4) MSx10mm Bolts (Part BB) and (4) MS Nuts (Part CC).

Hose
Do not completely tighten the bolts at this time
7

3 Gas Tank Support Assembly
Connect Gas Tank Support (Part K) to the body using (4) M6x10mm Bolts (Part AA).
Tighten all bolts (AA) with a Phillips Screwdriver (not included).

M

Assembly (continued)
4 Door Assembly
Connect Door (Part H) to Front Left Leg (Part D) by inserting the door pin into the leg hinge as depicted in graphic.

D

5 Lava Rock
Place the Lava Rock (Part F) into the fire bowl.
Note: Ensure no lava rock is placed on the ignition portion of the burner. Then place the Cover (Part E).

Cover
Lava Rock

Ignition

NOTE: COVER MUST BE REMOVED WHEN BURNER IS IN OPERATION.
ENSURE UNIT IS COMPLETELY COOL BEFORE REPLACING COVER.
9

Assembly {continued)
6 Assembling the cylinder
Put the cylinder into the Gas Tank Support (Part K), and secure the cylinder by tightening the screw in the gas tank support. Connect the hose and regulator to cylinder.
NOTE: The propane cylinder is sold separately. Use a standard 20 lb. propane cylinder only. Put the hose away from the bowl base during connect the propane cylinder.

7

Installing the AAA battery

Open the igniter by turning counter-clockwise and place the AAA battery (Part DD) into the igniter. Replace igniter then turn clockwise to tighten.

o Do not overtighten igniter button.

AAA Battery
10

30 minutes.

please contact 866-552-2810 for further for further assistance” please contact 866-552-2810 for further for further assistance”

Check and clean burner/vent tubes for insects and insect nests. A clogged tube can lead to a fire.”
Allow 45 minutes for heat to dissipate.