C65172 Gaming Chair
Product Information
The product is an LED controller that allows users to control
the color and quantity of LED pixels. It has various functions,
such as automatic RGB switching mode, remote control pairing, LED
color adjustment, and LED quantity setting. The device is designed
to comply with Part 15 of the FCC Rules, ensuring it does not cause
harmful interference and accepts any interference received.
Product Usage Instructions
RGB Automatic Switching Mode
To enter the RGB automatic switching mode:
- Continuously press the AUTO button five times.
Remote Control Pairing
To pair the remote control with the receiving controller:
- Press the LOCK button for five seconds until the LED flashes in
green quickly. - To un-match, press the LOCK button for five seconds until the
LED flashes in white slowly.
LED Color Adjustment
To adjust the LED color:
- Continuously press the SETTING button five times until the LED
flashes in white once and then turns into all white. - Press the R button until the LED turns red.
- Press the G button until the LED turns green.
- Press the B button until the LED turns blue.
- Finally, press the SETTING button once to finish your
setting.
LED Quantity Setting
To adjust the quantity of LED pixels:
- Press the SETTING button for five seconds until the LED flashes
in white to enter the setup menu. - Use the MODE +/- or SPEED +/- buttons to add or reduce the
quantity of LED pixels. - Finally, press the SETTING button once to finish the
setting.
Note: Different kinds of LED may not perfectly match the RGB
keys. If needed, reorder them.
Interference Troubleshooting
If the equipment causes interference to radio or television
reception, try the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver. - Connect the equipment into an outlet on a different circuit
than the receiver. - Consult the dealer or an experienced radio/TV technician for
help.
The device complies with FCC regulations and can be used without
restriction in portable exposure conditions.
outward
V*1
outward
Vx1
Continuously press “AUTO” 5 times to enter the RGB automatic switching mode,which can test the your LED.
Press “LOCK” for 5 seconds until LED flash in green quickly to match theremote control with the receiving controller. Press “LOCK” for 5 seconds untill LED flash in white slowly to un-match.
Different kinds of LED,the RGB keys may don’t perfectly match to your LED, reorder them if needed. Continuously press “SETTING” 5 times until LED flash in white once and then turn into all white, press the “R” until LED is red, press “G” until LED is green, press “B’ untill LED is blue, finally press “SETTING” once to finish your setting.
Adjust the LED quantity
Press “SETTING” for 5 seconds until LED flash in white to enter the setup menu. Press “MODE +/-” or “SPPED+/-” to add/reduce the quantity of the LED pixels.Finally press “SETTING’ once to finish the setting.
FCC Warning Statement: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
